2700W ZVS Induction Heating Heater Miniature Metal Quenching DIY Casting Furnace

Description

2700W ZVS Induction Heating Heater Miniature Metal Quenching Melting Furnace
Induction Heater is New, Power Supply is Used (second-hand).If the Power Supply AC 110V Input, Power Rated is about 1200 Watts. AC 220V Input, Power Rated is about 2700 Watts
Application
DIY small iron and steel parts for quenching, annealing heat treatment, melting point below 1500° C metal smelting (
Graphite crucibles)
,
CNC Tool Heating， small electromagnetic furnace, etc.
Only iron can be heated directly. Gold, Silver, Copper and other non-ferrous metals can not be heated directly. Graphite crucibles should be arranged to be heated in crucibles.
For larger parts, it is recommended to add an ammeter to monitor the current to prevent the main board from burning down.
small iron and steel parts for quenching, annealing heat treatment, melting point below 1200 C metal smelting, DIY small electromagnetic furnace, etc
1. Size: 120*265*105 (unit: mm); Copper Coil: ID 60mm
2. Working voltage: DC48V
3. Maximum operating voltage:DC48V (Maximum)
4. Maximum operating power: 2700W
(Maximum)
5. Maximum working current: 57A
(Maximum)
6.
If the heater not to work, Please turn off the power supply and extend the heater service life.
1. In any case, can not no-load must install the copper tubing(no load is placed on the output port of the empty load). If do not install the copper tubing, once the power is turned on, the board will emit high-frequency noise, which will result in complete destruction of the MOS tube.
2. When using a switching power supply, care must be taken because high-power switching power supplies typically have a slow-start function, that is, they slowly rise at the beginning of the output voltage, and if the voltage rises to 11V, the induction heating circuit is turned on because the voltage is insufficient. Cause the circuit does not start vibration, so that the two MOS tube at the same time conduction and burned components, so be sure to switch power supply voltage stability and then access the induction heating circuit;
3. This circuit is very strict power supply requirements, 36V is greater than 2000W, 48V is greater than 2600W;
4. No matter what voltage is used, as long as the operating current is less than 50A, the circuit will not be burned out. Therefore, a 50A fuse can be used to protect the circuit during high-power operation.
5. High-power operation is inevitable due to heat, so you should use the fan top blow to effectively dissipate heat while working.
6. Copper pipe and water pipe connections, the need to seal to prevent water leakage.
Special Attention
When the heater working the copper coil is very heating, need to increase water cooling.
Power Supply
Input AC 100-120V; 50/60Hz; 17A                            Output= DC 48V 25A 1200W
Input AC 200-240V; 50/60Hz; 17A                            Output= DC 48V 57A 2700W
LxWxH=30x11x4.5mm
Weight=2Kg
3000 watts of output power need to be connect to AC 220V
Package Included:
Package 1
1x 2700W Induction Heater Module
1x Copper Coil
1x Mini Water Pump
1x 12V 2A Adapter
1x 2M Water pipe
1x Graphite crucible,1x Ceramic Shield.
1x 2700W PSU when AC 220V Input.
1x Air switch
Package 2
1x 2700W Induction Heater Module
1x Copper Coil
1x Mini Water Pump
1x 12V 2A Adapter
1x 2M Water pipe
1x Graphite crucible,1x Ceramic Shield.
1x 2700W PSU when AC 220V Input.
1x Air switch
1x DC Current and Voltage Monitoring Module
Not accept P.O.BOX
address
International Buyers ? Please Note:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are afforded by the buyer.
Please check with your country? customs office to determine what these additional costs will be prior to bidding/buying.